The amphour (AH) capacity is the basis for rating motorcycle batteries. For example Cheap Marcus Thornton Jersey , a 12AH battery can produce one amp of current flow for 12 hours, or two amps for six hours. In order to calculate the amount of time needed to use up a fully charged motorcycle battery by turning the lights on, we have to take power in watts, and divide it by voltage, which gives us the current draw in Amps. Therefore, a 72 watts beam and tail together Cheap KJ McDaniels Jersey , divided by 12 volts equals a 6-amp draw. So in 2 hours, the 12AH battery is dead.
Checking Motorcycle Battery:
If you decide to check if your new motorcycle battery is done correctly, follow this actual factory-recommended service procedure.
If the battery is not a maintenance-free type which doesn't have a vent tube, unwrap the battery, unkink the vent tube and snip about a half-inch off the end. Fill it with electrolyte midway (between the high and low level markings on the case) and leave it undisturbed for one or two hours. Remember, the battery will still be at only 65% of full charge at this point. Add electrolyte again if required.
If your battery is a refillable lead-antimony type Cheap Randy Foye Jersey , it should be charged at one-third of its rated capacity in amphours for four to five hours to get it to full charge. Maintenance-free type battery should be charged with a constant-current charger that can drive the charge with as much as 16.9 volts. This should be closely supervised so as not to exceed full charge.
Next, recheck the electrolyte level and add water if required. Let the battery cool so the case contracts enough to fit into its typically tight little holder. Run the new breather tube, if the battery comes along with one, carefully through the original factory routing.
Things to Remember when Charging the Battery:
1. First of all, it is important to remember that Red is positive and Black is negative in order to avoid any accidents such as short-circuits and nasty shocks.
2. The charger should be compatible with the motorcycle battery, and give a greater output than the battery voltage but not too high.
3. Make sure the connections are clean and the electrolyte is at the upper level Cheap Drazen Petrovic Jersey , and don't fill the cells up to the very top of the battery.
4. You can either use an optimizer on the battery which can effectively switch off the battery when it's charged and prevents overheating, or disconnect it manually.
5. It is recommended to put your battery on charge every two or three weeks.
6. An upper and lower level battery should have all the cells on the upper level, not over and never under the lower level.
7. For topping off the low cells, use only distilled water.
8. The minimum charge for a new batter should be at least for 8 hours.
9. If you have a dry battery, fill the cells slowly and leave the battery for around half an hour.
Applying Epoxy Coating to Garage Floors Home Repair Articles | May 30, 2009 If your garage floors need new life Wholesale Brooklyn Nets Jerseys , then a granite look epoxy finish might be a good option. Take a look at the benefits of one system on the market, and what it involves to apply to your garage.
I have been looking at a lot of different garage floors lately, and am really impressed with the Roll on Rock epoxy floor coatings. This floor system can give your dull concrete garage floor a new life, a floor with a great granite look finish. It comes in four different systems, most take about two days to fully apply, except System 4 Wholesale Nets Jerseys , which should only be professionally installed. But if you want a system to apply yourself, then you should go with System 2.
System 2 is 95% solid epoxy base, so it works better than a water based base coat, it is easy to apply and does not need a primer, the odor is very mild and it is not flammable. Some important requirements that Versatile Building Products had in mind when they developed this system include:
The epoxy does not bubble The epoxy adheres permanently to the concrete. It has a long chipping window for applying the flakes, so it gives you enough time to apply the epoxy and the flakes correctly before panic sets in. It uses about half the flakes for a great granite finish than most other systems Cheap Brooklyn Nets Jerseys , which saves money. Offers maximum protection regardless of the climate. Is hot tire resistant and not affected by most household chemicals. Has a high gloss top coat. Can be used inside or out, and will not yellow. Fast & easy to install!
So, when it comes to an epoxy system, what does fast and easy mean? Normally full application takes two days since you have to allow for drying time between the base and top coats, though sometimes it can be done in one day if the weather is good and you use an accelerant on the base coat to speed up drying time. Lets take a look at the basics of applying Roll on Rock to garage floors.
First, you have to clean the concrete using a degreaser to remove any surface? contaminants Cheap Nets Jerseys , and then allow the surface to dry for about 30 to 60 minutes.
Next, mix the two epoxy components for 2 minutes with a paint paddle. Evenly roll the primer onto garage floors with a lint free roller. Allow the epoxy to set for at least 20 minutes, but not longer than 60 minutes before broadcasting the chips.
Using spiked shoes, walk onto the epoxy and taking small handfuls of flakes, cast it onto the surface so that it looks even, kind of like casting grass seeds.
Let your garage floor dry overnight Wholesale Trevor Booker Jersey , then gather up any loose flakes using a squeegee, broom or blower. Then go over the entire surface with a flexible blade (squeegee) to make sure that the surface is smooth.
Angelz Gilden Forum
Thema drucken
20.02.2020 06:42
Antworten
